SLT CAT6 POE
Ethernet (10/100/1000) Surge Protection Device
The SLT Series CAT6 POE provides fast clamping and high energy handling capability.
Unit provides protection against Transient Voltages that exceed the nominal operating voltage of incoming data. Each line is protected against surge impulses up to 400A. The SLT CAT6 POE device works in series with the communication lines being protected; diverting harmful transient energies, while maintaining a tight clamp at the peak voltage. Units are designed to operate in a wide temperature range and are configured for 10/100/1000 Ethernet data or similar protocol.
Protects CAT6 POE data lines with 1000Mbps & 250Mhz
POE up to 100W
Solid state fail-safe design
Low shunt capacitance to reduce signal loss
RJ45 (female to female) Connection Method
Performance tested to verify compliance
Data/Comm
3D Preview
Load Current | Max Surge Current (8/20) Iₘₐₓ | Short-Circuit Current Rating (SCCR) | Repetative Impulse Rating (Iₙ) | On/Off Status⬥ | Housing Rating | Product Weight | Product Dimensions | Most Current Industry Standards | Surge Technology | Connector Form/ Type | Connector Method | Interface | Operating Temperature | Operating Frequency | Fusing | Listings & Certifications | Enclosure | Max. Operating Voltage | Max. Clamp Voltage | Energy Rating/ Wire | Response Time | Warranty | Series Resistance | Peak Pulse Power | Line - Load Sensitive | Breakover Voltage: (Line - Ground) | Attenuation Margin | NEXT | Data Transfer Rate | Power Sum NEXT | Return Loss | ACR | Power Sum ACR | ARC -F | PSACRF | Mounting | Relative Humidity | Terminals | Max. Circuits Protected | Modes of Protection | Continuous Current | Follow Current | Wire Range | Feedback | Remote Alarm Contacts | Remote Alarm contact capability (Nominal Volts/ Nominal Amps) | Remote Alarm Wire Size | Included Accessories |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
200 Amps | [See EDR Series] | 60 grams (2.1 Ounces) | MOV | 8P8C (RJ45) | Plug-in | -30 ℉ to +165 ℉
( -34 ℃ to +74 ℃) | Polycarbonate | 92 Volts | < 1 Nanosecond | 3 Year Limited Product Warranty | 1500 Watts Min. (6000 Max) | No | 68 Volts | .3db @ 176MHz | >40dB | 10/100/1000Mbps | 47.8dB @ 248MHz | 34.8dB @ 38MHz | Worse Case 17.0dB | Worse Case 14.9dB | 27.4dB @ 245MHz | >38dB | 35mm DIN or panel mount via 2 integrated tabs that accept up to #6 sized screws | 95% noncondensing |
Specifications
Specification | Value |
|---|---|
Max Surge Current (8/20) Iₘₐₓ | 200 Amps |
Housing Rating | [See EDR Series] |
Product Weight | 60 grams (2.1 Ounces) |
Surge Technology | MOV |
Connector Form/ Type | 8P8C (RJ45) |
Connector Method | Plug-in |
Operating Temperature | -30 ℉ to +165 ℉
( -34 ℃ to +74 ℃) |
Enclosure | Polycarbonate |
Max. Clamp Voltage | 92 Volts |
Response Time | < 1 Nanosecond |
Warranty | 3 Year Limited Product Warranty |
Peak Pulse Power | 1500 Watts Min. (6000 Max) |
Line - Load Sensitive | No |
Breakover Voltage: (Line - Ground) | 68 Volts |
Attenuation Margin | .3db @ 176MHz |
NEXT | >40dB |
Data Transfer Rate | 10/100/1000Mbps |
Power Sum NEXT | 47.8dB @ 248MHz |
Return Loss | 34.8dB @ 38MHz |
ACR | Worse Case 17.0dB |
Power Sum ACR | Worse Case 14.9dB |
ARC -F | 27.4dB @ 245MHz |
PSACRF | >38dB |
Mounting | 35mm DIN or panel mount via 2 integrated tabs that accept up to #6 sized screws |
Relative Humidity | 95% noncondensing |
Diagrams
Not To Scale
Electrical Ratings
Click on any SLT CAT6 POE model from the table to request a quote
Model Number | TYPE | VPR | L-G (VPR) | MAX # Wires | Protocol |
|---|---|---|---|---|---|
SLT-SM-080-BCL3-RJ/POE | DC | 92V | 68V | 8 | Closed Loop |
NOTE: Installation is accomplished by simply inserting the Protector in series with the communication cable(s) and connecting the grounds as required. dB values obtained with a 300 ft long cable.
