SLT Series
Data/Signal Surge Protection Device
Transient Voltage Surge Suppression for standard low speed data (13.5MHz max), communication and signal line protocols. Units provide protection against Transient Voltages that exceed the nominal operating voltage of incoming data. Each line is protected against surge current impulses up to 10kA.
The SLT device works in series with the communication lines being protected, diverting harmful transient energy while maintaining a tight clamp at the peak voltage. Units are designed to operate in a wide temperature range and are configured for EIA (Electronic Industries Association)protocols. The built in floating ground connection allows the device to provide protection at remote locations without creating a ground loop noise problem.
Solid state fail-safe design
Low shunt capacitance to reduce signal loss
Performance tested to verify compliance
Data/Comm
3D Preview
Load Current | Max Surge Current (8/20) Iₘₐₓ | Short-Circuit Current Rating (SCCR) | Repetative Impulse Rating (Iₙ) | On/Off Status⬥ | Housing Rating | Product Weight | Product Dimensions | Most Current Industry Standards | Surge Technology | Connector Form/ Type | Connector Method | Interface | Operating Temperature | Operating Frequency | Fusing | Listings & Certifications | Enclosure | Max. Operating Voltage | Max. Clamp Voltage | Energy Rating/ Wire | Response Time | Warranty | Series Resistance | Peak Pulse Power | Line - Load Sensitive | Breakover Voltage: (Line - Ground) | Attenuation Margin | NEXT | Data Transfer Rate | Power Sum NEXT | Return Loss | ACR | Power Sum ACR | ARC -F | PSACRF | Mounting | Relative Humidity | Terminals | Max. Circuits Protected | Modes of Protection | Continuous Current | Follow Current | Wire Range | Feedback | Remote Alarm Contacts | Remote Alarm contact capability (Nominal Volts/ Nominal Amps) | Remote Alarm Wire Size | Included Accessories |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
400 mA | 10 kA per wire | [See EDR Series] | 14 Ounces | ANSI/UL 497B | MOV, SAD | Terminal | Terminal Strip Screw | -40 ℉ to +185 ℉
(-40 ℃ to + 85 ℃) | Up to 50Mhz | Listed to ANSI/UL 497B | Plastic (ANSI/UL Rated 94 5V) | 1.5 to 270 V DC | 7.5 - 220 V available | < 1 Nanosecond | 10 Year Limited Product Warranty | 2.7 Ohms (nominal) | 35mm DIN or panel mount via 2 integrated tabs that accept up to #6 sized screws | 95% noncondensing | DIN Clip Kit |
Specifications
Specification | Value |
|---|---|
Load Current | 400 mA |
Max Surge Current (8/20) Iₘₐₓ | 10 kA per wire |
Housing Rating | [See EDR Series] |
Product Weight | 14 Ounces |
Most Current Industry Standards | ANSI/UL 497B |
Surge Technology | MOV, SAD |
Connector Form/ Type | Terminal |
Connector Method | Terminal Strip Screw |
Operating Temperature | -40 ℉ to +185 ℉
(-40 ℃ to + 85 ℃) |
Operating Frequency | Up to 50Mhz |
Listings & Certifications | Listed to ANSI/UL 497B |
Enclosure | Plastic (ANSI/UL Rated 94 5V) |
Max. Operating Voltage | 1.5 to 270 V DC |
Max. Clamp Voltage | 7.5 - 220 V available |
Response Time | < 1 Nanosecond |
Warranty | 10 Year Limited Product Warranty |
Series Resistance | 2.7 Ohms (nominal) |
Mounting | 35mm DIN or panel mount via 2 integrated tabs that accept up to #6 sized screws |
Relative Humidity | 95% noncondensing |
Included Accessories | DIN Clip Kit |
Diagrams
Not To Scale
Electrical Ratings
Click on any SLT Series model from the table to request a quote
Model Number | Service Voltage | TYPE | MAX # Wires | Protocol |
|---|---|---|---|---|
SLT-XM-04-S-U-CL1-TS | 30Vdc | DC | 4 | Closed Loop |
SLT-XM-04-S-U-CL2-TS | 55Vdc | DC | 4 | Closed Loop |
SLT-XM-04-S-U-DC1-TS | 95Vdc | DC | 4 | DC Power |
SLT-XM-04-S-U-DC2-TS | 130Vdc | DC | 4 | DC Power |
SLT-XM-04-S-U-DC3-TS | 195Vdc | DC | 4 | DC Power |
SLT-XM-04-S-U-DC4-TS | 18Vdc | DC | 4 | DC Power |
SLT-XM-04-S-U-DC5-TS | 140Vdc | DC | 4 | DC Power |
SLT-XM-04-S-U-SL1-TS | 25Vac | AC | 4 | Signal Line |
SLT-XM-04-S-U-SL2-TS | 10Vac | AC | 4 | Signal Line |
SLT-XM-04-S-U-SL3-TS | 270Vac | AC | 4 | Signal Line |
SLT-XM-04-S-U-SL4-TS | 45Vac | AC | 4 | Signal Line |
SLT-XM-04-S-U-SL5-TS | 50Vac | AC | 4 | Signal Line |
SLT-XM-10-S-U-CL1-TS | 30Vdc | DC | 10 | Closed Loop |
SLT-XM-10-S-U-CL2-TS | 55Vdc | DC | 10 | Closed Loop |
SLT-XM-10-S-U-DC1-TS | 95Vdc | DC | 10 | DC Power |
SLT-XM-10-S-U-DC2-TS | 130Vdc | DC | 10 | DC Power |
SLT-XM-10-S-U-DC3-TS | 195Vdc | DC | 10 | DC Power |
SLT-XM-10-S-U-DC4-TS | 18Vdc | DC | 10 | DC Power |
SLT-XM-10-S-U-DC5-TS | 140Vdc | DC | 10 | DC Power |
SLT-XM-10-S-U-SL1-TS | 25Vac | AC | 10 | Signal Line |
SLT-XM-10-S-U-SL2-TS | 10Vac | AC | 10 | Signal Line |
SLT-XM-10-S-U-SL3-TS | 270Vac | AC | 10 | Signal Line |
SLT-XM-10-S-U-SL4-TS | 45Vac | AC | 10 | Signal Line |
SLT-XM-10-S-U-SL5-TS | 50Vac | AC | 10 | Signal Line |
*NOTE: Installation is accomplished by simply inserting the Protector in series with the communication cable(s) and connecting the grounds as required.
Replace X with: A for SAD Arrays, C for 5kA (Commercial), I for 10kA (Industrial) S for Solid State.
Compatibility Table
EDR Model Number | PVA50-1P-xxxv-S | PVA50-2P-xxxv-S | PVA50-3P-xxxy-S | PVA50-5P-xxxy-S | DRA50-1Pxxx-S | DRA50-2Pxxx-LGN | DRA50-2Pxxx-S | DRA50-3Pxxx-S | DRA50-3PSxxx-S | DRA50-4Pxxx-S | CLT-xxx | SLT CAT X/X-POE | SLT/XM-02- | SLT/XM-04- | SLT/XM-06- | SLT/XM-10- | TST010/XXX | TST020/(120-250v) | TST020/(24-48v) | TST040/XXX |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
